891 reviews analysed
1. BCZAMD 24V 50W Upgraded Ceramic Cartridge Heater Wire 1M 3D Printer Accessories Heating Tube 620mm for Reprap Prusa Mendel i3 MK3 MK10 Maker Select V2 3D Printer Parts V6 Hotend J-head Extruders, 3Pcs
Feature
- Apply to Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Anet A8, Maker Select V2.1, Monoprice v2, Wanhao Duplicator 3D Printer, V6 Volcano MK8 MK9 MK10 Extruder/Hotend etc.
- The improvement compared to ordinary red heating tube:
- 1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- 2.From the original 40W power to 50W, the maximum temperature increases from 300-31℃ to 340-350℃. Can be used with the new HT-NTC100K temperature thermistor.
- 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
Description
After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you
Specification
Voltage: 24V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">
Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.
Package listing:
3 x 24V 50W Ceramic Cartridge Heater
2. BCZAMD 12V 50W Upgraded Ceramic Cartridge Heater Wire 1M 3D Printer Accessories Heating Tube 620mm for Reprap Prusa Mendel i3 MK3 MK10 Maker Select V2 3D Printer Parts V6 Hotend J-head Extruders, 3Pcs
Feature
- Apply to Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Anet A8, Maker Select V2.1, Monoprice v2, Wanhao Duplicator 3D Printer, V6 Volcano MK8 MK9 MK10 Extruder/Hotend etc.
- The improvement compared to ordinary red heating tube:
- 1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- 2.From the original 40W power to 50W, the maximum temperature increases from 300-31℃ to 340-350℃. Can be used with the new HT-NTC100K temperature thermistor.
- 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
Description
After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you
Specification
Voltage: 12V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">
Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.
Package listing:
3 x 12V 50W Ceramic Cartridge Heater
3. MakerHawk 5pcs Aluminum Heater Block for MK7 / MK8 3D Printer and 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and 5pcs 12V 40W 620 Ceramic Cartridge Heater for 3D Printer
Feature
- 3d printer heater block: Inner hole for set screw: M6 and M3 (heat pipe and thermocouple).
- 12V 40W 620 Ceramic Cartridge Heater: Resistance: Material: 304 stainless steel
- Lead wire: 0.3 square
- 2080 high temperature resistant high quality oxide powder.
- NTC 3950 100K Thermistor: For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
- Resistance value at 25°C=100K
- Cartridge Heater: The solids, liquids, and gases need to be heated by cartridge heater, transmit heat quickly by conduction if the producer of the heat (the cartridge) is in direct contact with the heat sink (any solid, liquid, or gas)
- Widely used for manufacturing plastic and rubber parts in the car industry or in the food processing industry, etc
- We have a strong after-sales team, if you have any questions, please feel free to email us. Click on “MakerHawk-US”,then “Ask a question”.We will reply to you as soon as possible. Thank you for your cooperation!
Description
3d printer heater block:
Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)
Heater Mounting Hole: 6mm diameter
Thermocouple Mounting Holes: 3mm diameter
Suitable for Makerbot printer
12V 40W 620 Ceramic Cartridge Heater:
Material: 304 stainless steel
Lead wire: 0.3 square
Resistance: 2080 high temperature resistant high quality oxide powder
Application:
1 Semiconductor chamber heating
2 Semiconductor wafer lead connection
3 Semiconductor wire and die bonding
4 Freeze protection and deicing of equipment in cold climates or applications
5 Humidity Control
6 Patient Comfort heating used in medical devices
7 Mold die and platen heating
8 Seal bars used in packaging equipment
9 Test sample heating in gas chromatography
NTC 3950 100K Thermistor:
For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
Small Size: 1.25mmx2.0mm glass bead
High accuracy: 1%
Resistance value at 25°C=100K
Wiring insulation: high temperature teflon / PTFE
Package Including
5 * 3d printer heater block
5 * 12V 40W 620 Ceramic Cartridge Heater
5 * NTC 3950 100K Thermistor
4. Ewigkeit 12V 40W Ceramic Cartridge Heater and 3950 100K NTC Thermistor with Female Pin Head for RepRap 3D Printer Heatbed or Hot End
Feature
- Thermistor Color : white,Cartridge Heater Material: 304 Stainless Steel
- Voltage: 12v, Power: 40w,Diameter: 6mm
- Length: 20mm
- Temperature sensor 100KΩ accuracy of ± 1%
- Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring
- Support for NTC 3950 is included in Marlin firmware, use TEMP_SENSOR 11 in firmware configuration
5. 12V 40W 1/4-in (6.35mm) Ceramic Cartridge Heater for 3D Printer MK10 Extruder/Hotend
Feature
- 12 Volt 40 Watt (12v 40w) MK10 3D Printer Ceramic Heater Cartridge with a 1/4-in (6.35mm) Diameter and 1m Wire
- Designed to be the proper OEM fit for 3D printers with a MK10 extruder and a 6.35 mm (1/4 inch) heater block bore
- Compatible with Wanhao Duplicator i3, FlashForge Creator, Monoprice Maker Select v1/v2/v2.1 FDM/FFF Printers with 1/4in heater hole
- Length: 20mm / Diameter: 6.35mm – Wire Length: 100cm
- 1/4 (0.25in) US Standard Size Often Hard to Find – Used on many American and Chinese Made 3d Printers designed for the US Market
Description
12V 40W 1/4-in (6.35mm) Ceramic Cartridge Heater
Fits Many MonoPrice/Flashforge/Wanahoo MK10 3D Printers with a 1/4in 6.35mm Bore Heater Hole
Please NOTE: This is a variation listing – You must select your voltage (12v or 24v) from the drop down menu at the top of the page
Specifications: Product: Single-head heating tube
Diameter: 1/4 inch / 6.35mm Length: 20mm
Wire Length: 3ft 3in / 1m Voltage: 12 Volt
Power: 40 Watt
Package Contents: 1pc – 40W 12V Ceramic Heater Cartridge with a 1/4-in (6.35mm) Diameter
6. WINSINN 12V 50W Heater Cartridge 620 Heating Tube HT-NTC100K Thermistor 1M for Ender 3 CR-10 Sensor Heater Block V6 J-Head Hotend Extruder 3D Printer (Pack of 5Pcs)
Feature
- ✔️Voltage: 12V, Power: 50W, Head diameter: 6mm, Head length: 20mm, Total length:1 Meter
- ✔️From the original ordinary 0.3-line high-temperature line to 0.6-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- ✔️From the original 40W power up to 50W, therefore, the maximum temperature increases from 300-310℃ to 340-350℃ or so.
- ✔️The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
- ✔️Made by WINSINN. Can be used with the New Sensor Heater Block (Temperature measurement can be up to 350 degrees).
Description
►Voltage: 12V
►Power: 50W
►Heating head size: 6 x 20mm
►Total length:1 Meter
►Heating head material: 304 stainless steel
►Heating temperature: up to 350 degrees
►Fit for New Sensor Heater Block
—————————————————————————————————————
Package include:
►5 x 12V 50W Ceramic Cartridge Heater
———————————————————————————————————————
Product Warranty:
-WINSINN are devoted to offer premium quality products to all cherished customers. Meanwhile supply 60 days money back guarantee and 24 months warranty.
-If there are any questions, please feel free to contact us, WINSINN Customer Service Team will spare no efforts to assist with you within 24 hours.
7. Signstek 10 PCS Reprap 12V 40W 620 Ceramic Cartridge Heater for 3D Printer Prusa Mendel
8. R REIFENG Heating Tube 620mm Reprap 24V 50W Thermistor Ceramic Cartridge Heater for Hotend J-Head Extruder 1M 3D Printer Parts(Pack of 2)
Feature
- From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- The original 40W power to 50W, therefore, the maximum temperature increases from 300-31℃ to 340-350℃
- The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
- Support the customization of different specifications, length, resistance of the heater.
- Can be used with the new HT-NTC100K temperature thermistor (Temperature measurement can be up to 350 degrees).
Description
Product specification
Voltage: 12V/24V
Power: 50W
Heating head size: 6 * 20mm
Heating head material: 304 stainless steel
Line length: 1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Heating temperature: up to 350 degrees
Package included:
2 Pcs
Single-ended heater instructions
1. The effective heating part of the heater must keep dry.
2. The electrical connector of the single-ended heater should be placed out of the insulation layer and heating room, and the working voltage shall not exceed its rated value of 10%. The shell should be effectively grounded.
3. Electric components working environment, the temperature should not be greater than 95 degrees, no explosive or corrosive gases.
4. Electric components should be stored in a dry place.
9. Sunhokey 6x20mm 100CM Cable Lenth 12V 40W Cartridge Heater for 3D Printer (12V 40W-6pcs)
Description
6x20mm 100CM Cable length 12V 40W Ceramic Cartridge Heater for 3D Printer.
Notes: The heating wire should not be bent. The product will be damaged after bending. If the product you received is not available, please contact us and we will provide satisfactory after-sales service for customers.
★The cartridge heater consists of a cylindrical stainless steel tube and thus provide high corrosion resistance.
★The inner heating wire is wound around the ceramic core.
★The number of coils varies according to power and provides a large uniform distribution of heat, which significantly increases the long life of the heater and prevents oxidation of the heater wire even at high temperatures.
Safety Guide:
★Recommend Safe Working Temperature: ＜300°C
★Must pay attention to the Safe working temperature of the 3D printer’s consumable and accessories, May cause high-temperature hazards!!
PLA (190°C-210°C)
ABS (230°C-250°C)
Warning!!
*This product is designed for 3D printers, always shut off the power of the circuit before starting installation work.
*3D printer accessories temperature can be very high, pay attention to safety!
*Due to the variety of possible uses, it is ultimately the responsibility of the customer to determine a product’s suitability for a particular application.
Conclusion
By our suggestions above, we hope that you can found Wanhao Heating Cartridge for you.Please don’t forget to share your experience by comment in this post. Thank you!
