Top 10 Frigidaire Gallery Side Dishwasher Mount

This is a Genuine Replacement Part,The Model Number and Name for The Following Item: Frigidaire (FRIGB) 154657901 Mounting Clip.

This is a genuine replacement part, the model number and name for the following item: Frigidaire (frigb) 154428403 tine clip.

This is a genuine replacement part, the model number and name for the following item: Frigidaire (frigb) 154610501 mounting bracket.

This is a Genuine Replacement Part,The Model Number and Name for The Following Item: Frigidaire (FRIGB) 154654601 Mounting Clip.

1) Turn off power to dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) and turn off water supply. 2) Pull dishwasher out from its place. 3) Remove upper screw from side of dishwasher. Align last hole of bracket on long flat part of bracket with screw hole. Reinsert & tighten removed screw or one of new provided screws. 4) Push dishwasher back into place. Open dishwasher door. Determine which bracket hole you will use. You want to use the farthest hole forward that still attaches to cabinet. If using holes on the smaller flat part of bracket, see 5A-6A. If you need to use back hole, see 5B-9B. 5A) If using front hole, leave bracket as is. If using 2nd hole, use 1 pair of pliers to hold bracket at the 2nd hole & 1 pair of pliers to break off front tab. Repeat. Push dishwasher back into place. 6A) Pre-drill screw holes to avoid splitting wood. Screw brackets into place using provided screws. DONE! 5B) If you cannot use either of front two holes on bracket, you will need to drill a hole in the tub. Use a sharpie to mark through back bracket hole on dishwasher. Repeat. Remove both brackets. 6B) Using 2 sets of pliers, break off both brackets before bend. 7B) Drill 3/8 inch hole through each side of plastic tub. Hold plastic tightly right below mark & use a drill slowly to ensure you have a nice clean hole without damaging the tub. Clean up both holes with razor blade until smooth. 8B) Put brackets back on, put dishwasher back into place. Pre-drill small holes into the cabinet wood, then screw in included screws on each side. 9B) Insert plastic plugs in each hole. Run dishwasher & check for leaks. If leaks are present, you may need to add rubber cement to plastic plugs to create a seal. This is a generic product manufactured & distributed by Impresa Products (TM). This is not a Frigidaire (TM) / Electrolux (TM) OEM product. Any use of Frigidaire (TM) or Electrolux (TM) brand names, models, etc. are made solely to describe & illustrate compatibility.

Comparable to OEM Parts include WP8269145, 8269145, EA393134, AP3039168, PS393134, 830941, AH393134 and many more.

FIXES THE FOLLOWING SYMPTOMS:
Door latch failure.
Door won’t close.

INSTRUCTIONS:
1. Turn off the power and water supply to avoid shock.
2. Open the dishwasher door and use a phillips screw driver to remove the screws that hold the dishwasher to the cabinet.
3. Close the dishwasher door and use it to pull the dishwasher out from the counter top. You only need to pull out far enough to expose the brackets.
4. The undercounter brackets are held in by the bent tabs on the bracket that hold the bracket in place. Straighten out the tabs and slide the bracket out.
5. Slide the dishwasher brackets into the same area you removed the original brackets and bend the tabs to secure the brackets to the dishwasher.
6. Finish by carefully sliding your dishwasher back under the cabinet. Use your provided screws to screw the dishwasher bracket directly to the underside of your counter with a Phillips screwdriver.

WHAT YOU GET:
2 x Dishwasher Mounting Brackets
2 x Mounting Screws

100% CUSTOMER SATISFACTION :
Feel free to contact us if you have any questions or problems with the item

1) Turn off power to your dishwasher in breaker box (ABSOLUTELY CRITICAL TO AVOID SHOCK) 2) Rotate lower access panel fasteners and remove them 3) Remove access panel/sound dampening pad. Determine if the water supply/power lines have enough slack to move the dishwasher. If not, you will need to turn off water supply valve, disconnect water supply line from inlet valve & release power line from junction box 4) Open dishwasher door, remove the screws from the existing brackets (if present) 5) You will next be moving the dishwasher. To do so, you may need to lower the dishwasher by adjusting the leveling legs 6) Carefully pull dishwasher a few inches away from the front of the cabinet 7) Use pliers to pull up tabs in back of the bracket (if present). Pull out old brackets 8) Insert new brackets. Use pliers to adjust the back tab to lock the brackets in place 9) Slide the dishwasher back into the cabinet (readjusting the leveling legs, if necessary). Replace the screws in your new brackets 10) Reverse steps 3, 2 and 1. ALL SET! This is a generic product manufactured and distributed by Impresa Products (TM). This is not a Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) or Inglis (TM) OEM product and Impresa Products has no affiliation with or endorsement from these brands. Our product is not covered under any other manufacturer’s warranty (except for Impresa Products). The Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names and logos are the registered trademarks of their owners. Any use of the Whirlpool (TM), Sears (TM), Kenmore (TM), Amana (TM), Jenn-Air (TM), Crosley (TM), Maytag (TM), Roper (TM), Magic Chef (TM), Estate (TM) and Inglis (TM) brand names, model or any other related designations are made solely for purposes of describing and illustrating compatibility.

12-Pack undercounter dishwasher upper mounting bracket replacement and 24 installment screws, dishwasher undercounter mounting kit

Many features:
Replace part numbers: compatible with 8269145/ WP8269145, AP3039168, PS393134, 830941, AH393134, EA393134, sufficient quantity for you to replace the old or broken one.

Easy to install:
The dishwasher bracket kit can be installed quickly and easily with a screwdriver and needle-nosed pliers, saving the hassle and time.

Compatible with:
These dishwasher replacement parts compatible with Sears, Kenmore, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef and other dishwashers.

Specification:
Color: as the pictures shown
Material: durable steel
Size: 1 x 1.6 inch

Package includes:
12 x Undercounter dishwasher upper mounting bracket replacement
24 x Installment screws

Pleased note:
This is an aftermarket product (not original ), the mention of any related models and brands above is only for purposes of demonstrating compatibility.